This connecting screw is made to anchor your dock to dead weight without visible chains those being attached directly under the dock this way limiting their access to criminals. However, due to limited access, we do not recommend the use of this kind of anchorage if water level variations are superior to 2' (0,75 m).

* Also available in beige #ST 007

This stainless steel anchorage ring allows you to attach a chain from the dead weight to the dock. To be installed through an exterior lug connector. The ideal product for salted water plus it gives you the possibility to easily adjust the tension of the chains.

Wall anchorage gives you the possibility of anchoring your dock to a vertical wall. The complete system is made of stainless steel. It can swivel around to follow the wave motion. Mounted on nylon pivots, it is extremely quiet. It will take only a few seconds to unhook your dock from its anchorage point. However, since it is fixed, this system should not be used when there is a water level variation.

You can also use this product to anchor one of our docks, our Jetslide, or any another type of floating dock.

The adjusting chain is an economical type of anchorage for small installations. It gives you the opportunity to adjust your anchorage easily, so it can adapt to water level variations during the season.

The post cube has a cylindrical opening to fit a 2 7/8¨ diameter galvanized steel pipe needed to anchor your installation. This post is also covered with a 3¨ interior diameter PVC cover and a cap. This is used not only to hide the metal pole but also to give a better plastic on plastic movement with the post cube. This particular type of anchorage is very resistant and allows your installation to follow water level variations. This is the ideal anchorage for tidal areas. Note that this system should not be used in zones where the depth is over 7' (2,25 m).

* Also available in beige # ST 003

This half post cube is used with half cubes. The half post cube has a cylindrical opening to fit a of 2 7/8¨ diameter galvanized steel pipe that will be used to anchor your installation. This post is also covered with a galvanised 3” PVC interior diameter and cap. This is used not only to hide the metal pole but also to give a better plastic on plastic movement with the post cube. This particular type of anchorage is very resistant and allows your installation to follow water level variations. This is the ideal anchorage for tidal areas. Note that this system should not be used in zones where the depth is over 7' (2,25 m).

*Also available in gray #ST 004

Candock uses a grade 30 5/16" galvanized steel chain for its anchorages.

Candock can also provide if needed disk type dead weights with a central opening to pass chains through it. Easy to handle and can be added to increase the anchorage weight.

Standard galvanized steel post used by Candock for anchorage with the post cube.

Standard galvanized steel post used by Candock with starting anchorage cubes when you have a small or medium size installation and when the bottom of the lake permits it (not fit for a rocky bottom). We recommend using 2 posts on each side when starting your installation at a 2-cube distance in between. The top of the posts should be covered with a cap for 1 11/16¨ post for safety reasons.

Safety cap to be used with 1 11/16" pipe.

PVC cover used for 2 7/8" posts when you have a post cube for anchorage in your installation.

Cap used to cover the PVC posts. Required when you have a post cube in your installation. We recommend to glue and screw it.

Support that permits the insertion of a 1 11/16'' pile used to anchor a dock or jetslide by sliding the pile through the tabs of the cubes. (see picture)

Support that permits the insertion of a 1 11/16'' pile used to anchor a dock or jetslide by sliding the pile through the tabs of the cubes. Pile must be inserted into the sea bed.(see picture)

Wall anchorage gives you the possibility of anchoring your dock to a vertical wall. The complete system is made of steel covered with a high resistance cooked paint. It's recommended to use the stainless wall anchorage when used in a salty environement. It can swivel around to follow the wave motion. Mounted on nylon pivots, it is extremely quiet. It will take only a few seconds to unhook your dock from its anchorage point. However, since it is fixed, this system should not be used when there is a water level variation. You can also use this product to anchor one of our docks, our Jetslide, or any another type of floating dock.

Candock can also provide if needed disk type dead weights with a central opening to pass chains through it. Easy to handle and can be added to increase the anchorage weight.

The post cube has a cylindrical opening to fit a 2 7/8¨ diameter galvanized steel pipe needed to anchor your installation. This post is also covered with a 3¨ interior diameter PVC cover and a cap. This is used not only to hide the metal pole but also to give a better plastic on plastic movement with the post cube. This particular type of anchorage is very resistant and allows your installation to follow water level variations. This is the ideal anchorage for tidal areas. Note that this system should not be used in zones where the depth is over 7' (2,25 m).

* Also available in beige # ST 012

This half post cube is used with half cubes. The half post cube has a cylindrical opening to fit a of 2 7/8¨ diameter galvanized steel pipe that will be used to anchor your installation. This post is also covered with a galvanised 3” PVC interior diameter and cap. This is used not only to hide the metal pole but also to give a better plastic on plastic movement with the post cube. This particular type of anchorage is very resistant and allows your installation to follow water level variations. This is the ideal anchorage for tidal areas. Note that this system should not be used in zones where the depth is over 7' (2,25 m).

*Also available in beige #ST 016

Anchor rope equiped with an elastic core that permits adaptability to waves and tidal variations.

Also available for 2m/6ft:TTC 0608900 2M

Other lengths available upon request

This connecting screw is made to anchor your dock to dead weight without visible chains those being attached directly under the dock this way limiting their access to criminals. However, due to limited access, we do not recommend the use of this kind of anchorage if water level variations are superior to 2' (0,75 m).

* Also available in beige #ST 018

This HEAVY DUTY stainless steel anchorage ring allows you to attach a chain from the dead weight to the dock. To be installed through an exterior lug connector. The ideal product for salted water plus it gives you the possibility to easily adjust the tension of the chains.

Articulated system that permits an anchoring to the shore on different structures like: Walls, big rocks, etc.

ALSO 15'  RL 328